Fulltext results:
- Connection system @en:gdm_linear_axes
- a power cable and a signal cable with PTC sensor connections. ===== Power cable - DE20001270-5M ===== The GD... a power cable and a signal cable with PTC sensor connections. {{:ironcore_motors:l_series_1.jpg?nolink&600x24... le.jpg?direct&800x665}} Note: The thermal switch connections can also be in black color. In this case the cros... ies the motor phases and the thermal (PTC) sensor connections. - The **signal cable** carries the encoder signa
- MBM Motors connections @en:mbd_servo_drive
- ====== MBM Motors connections ====== This page describes the **MBM motor connections** on the MBD servo drive. The MBM motors are connected ... C6 connector.\\ STM+/STM- are the thermal sensor connections. HU, HV and HW are the commutation signals. A/B/Z... tor. - **STM+/STM-** are the thermal (PTC) sensor connections. - **HU, HV, HW** are the commutation (Hall) sign
- Cable coding system @en:mbm_motors
- eters|M15|flying-leads| |DE20000814-5M|with brake connections|5 meters|M15|flying-leads| |DE20000773-5M|with brake connections|5 meters|M17|flying-leads| |DE20000813-5M|with brake connections|5 meters|M40|flying-leads| |DE20000772-5M|with brake connections|5 meters|M23|flying-leads| ===== Signal cable ==
- Safety instruction @en
- symbol.jpg}}|High electrical voltage due to wrong connections! Danger to life or bodily harm by electric shock!... in the national regulations. | | Technical data, connections and operational conditions are specified in the p
- Maintenance @en:green_drive_iso
- notes below: |**Item** | | Check all electrical connections and all mechanical components and their safety op... ate of stator and the slider | | Check screws and connections | | Check the state of power and signal cables |
- Maintenance @en:green_drive_motors
- notes below: |**Item** | | Check all electrical connections and all mechanical components and their safety op... ate of stator and the slider | | Check screws and connections | | Check the state of power and signal cables |
- Accessories @en:integrated_drive_motors
- DBUS RTU or CANopen bus terminal block daisychain connections ==== {{https://www.nilab.at/wp-content/uploads/d... - DIGITAL INPUTS / OUTPUTS terminal block for PLC connections ==== {{https://www.nilab.at/wp-content/uploads/d
- Maintenance @en:integrated_drive_motors
- notes below: |**Item** | | Check all electrical connections and all mechanical components and their safety op... ate of stator and the slider | | Check screws and connections | | Check the state of power and signal cables |
- Programming box DA012060 - cable connections @en:integrated_drive_motors
- ====== Programming box DA012060 - cable connections ====== This page shows the **cable connections** of the programming box (DA012060) for the NLi integrated dri
- Electrical Connections @en:integrated_pick_and_place
- ====== Electrical Connections ====== ==== Connection between the two motors ==== The pick and place robot wor... ave. {{:integrated_pick_and_place:pick_and_place_connections_rev12.png?nolink&500x478}} The signal must be co
- Control Signals @en:integrated_pick_and_place
- = As explain the [[:en:integrated_pick_and_place:connections|connections description]], one signal called TRIGGER SIGNAL from PLC or Sensor is used to start the motion seq
- How to calculate the motor phase angle @en:mbd_servo_drive
- s U,V,W are not OK ⇒ Please check the power cable connections. | | The motor is moving without control reaching... s U,V,W are not OK ⇒ Please check the power cable connections. | {{:mbd_servo_drive:jog.png?direct&761x590}}
- Power Port Pinouts @en:nl7_servo
- ease refer to Regenerative resistor selection and connections| |Br|External regenerative resistor terminal|Please refer to Regenerative resistor selection and connections| |N| |Please do not connect| |U|Motor U phase ter
- Protection @en
- |**Item** | | improper or wrong wiring of cable connections | | incorrect operation of the equipment componen
- Elektrische Verbindungen @de:integrated_pick_and_place
- ren. {{:integrated_pick_and_place:pick_and_place_connections_rev12.png?nolink&500x478}} Das Signal muss wie i