Fulltext results:
- Protection @en
- |danger_e_symbol.jpg}} || | \\ **High electrical voltage! Danger to life, severe bodily harm by electric s... ction and safety regulations when working on high voltage installations. \\ * Before switching on power the... e. \\ * Before working with electrical parts with voltage higher than 50 V, the equipment must be disconnected from the mains voltage or power supply. \\ * Make sure the equipment can
- Force vs. speed curve @en
- se characteristic curves is defined by the DC bus voltage and the relevant motor-specific data, e.g. induct... ance, and the motor constants. Varying the DC bus voltage (different drives, power supplies, or supply volt... pg}} As velocity increases, the available DC bus voltage is reduced by the motor's back EMF. This leads to... s. For motors supplied with an unregulated DC bus voltage, voltage drops — for example from simultaneous ac
- Glossary @en
- position.\\ **Back EMF:** The peak phase-to-phase voltage generated when the motor is traveling at a veloci... **Commutation:** The switching sequence of drive voltage into the motor phase windings, necessary to ensur... g and there is no cooling.\\ **Continuous Working Voltage:** The maximum allowable continuous voltage between any two phases, or between any phase and the motor saf
- Drive with analog reference @en:mbd_servo_drive
- erential analog input 12bit\\ Differentials input voltage of max. ± 10 V\\ Connect the controller (PLC or N... a potentiometer and you do not have a ± 10V dual voltage power supply, the voltage can be derived using the following circuitry. The first diagram shows how to drive the motor with a voltage from 0 to 10V, the second one with a voltage from
- How a Tubular Linear Motor Works @en:engineersguide
- nt capability. | At higher speeds, back-EMF (the voltage generated by the moving magnets) reduces the avai... ed at which roll-off begins depends on the supply voltage and the motor's back-EMF constant (Ke). The relationship between peak velocity, supply voltage, and motor parameters is: **V_max ≈ (V_dc − I·R) / Ke** This is why selecting the correct bus voltage is important when high-speed operation is require
- GDi - Green Drive ISO 15552 @en:green_drive_iso
- to 70×70 mm. Windings are available for both high voltage (230/480 VAC) and low voltage (24/48 VDC). [[https://www.nilab.at/wp-content/uploads/ISO.jpg|{{https://ww... (45×45 mm and 70×70 mm) and 6 motor sizes. - High-voltage (230/480 VAC) and low-voltage (24/48 VDC) windings. - Integrated encoder feedback and thermal protection.
- Analog control @en:integrated_drive_motors
- nce here is 150 ohm, corresponding to an internal voltage of 3V. Using NILAB Starter software the user can... otors:current_control.jpg?nolink&600x253}} ===== Voltage control (0 to 10V) ===== Voltage control can be used for position, force and velocity control as the Anal
- Directives @en:mbd_servo_drive
- ves ====== The EMC Directive 2004/108/EC and Low Voltage Directive 2006/95/EC are mandatory for the supply... CE)\\ • EC EMC Directive (2004/108/EC)\\ • EC Low Voltage Directive (2006/95/EC)\\ The following rules must... ectrical Equipment in Machines)\\ EN 60439-1 (Low-voltage switchgear and controller assemblies)\\ The follo
- Electrical characteristics @en:motolab_actuator
- === |**Parameter** |**Unit** |**Value** | |Rated Voltage|V|24-48 VDC| |Minimum voltage|V|18 VDC| |Maximum voltage admitted|V|80 VDC| |Boost current (5sec)|A|120 A@5sec| |Peak current|A|100 A| |
- Holding brake @en:nl7_servo
- round motor with holding brake. | | 24V operating voltage for the holding brake has to be ensured to mainta... onality of the holding brake. Please consider the voltage dropped over lengthy motor cables due to increase... nt malfunctioning of the holding brake in case of voltage drop. | | If the motor is using a magnetic encode
- Safety instruction @en
- bol.jpg?nolink&110x127|danger_e_symbol.jpg}}|High voltage and high discharge current! \\ Danger to life or ... nk&110x117|warning_e_symbol.jpg}}|High electrical voltage due to wrong connections! Danger to life or bodil
- Servo Drive Label @en:epulse50_dc_servodrive
- * | | Model name | | Serial number S/N# | | Rated Voltage | | Rated Current and Peak Current | | CE marking... ts or requesting support. - Verify that the rated voltage and current on the label match the application. -
- Technical data @en:green_drive_iso_rotolinear
- ent (Rotary)|2|Arms| |Peak Current (Rotary)|8|A| |Voltage constant|88|V/krpm| |Torque constant|1.46|Nm/A| |... r axis. - The **rotary** values (torque, current, voltage constant, torque constant) refer to the rotary ax
- IP69K ISO Version @en:green_drive_iso
- to 70×70 mm. Windings are available for both high voltage (230/480 VAC) and low voltage (24/48 VDC). {{https://en.nilab.at/wp-content/uploads//GDI-IP69K.11.jpg?dir
- Liquid Cooled Motors (LK) @en:ironcore_motors
- with the cooling liquid and \\ A) have a certain voltage drop according to the electro-chemical voltage order and \\ B) are electrically connected so that an elect