Fulltext results:
- Encrypted Modbus RTU @en:integrated_drive_motors
- onse.\\ | | **Confidentiality** — the Modbus PDU (function code and register data) is encrypted. An observer... The encrypted frame replaces the standard Modbus function code and PDU with a fixed-structure wrapper identified by function code **0x65**: <code> Standard Modbus RTU (plaint... lculated over the entire frame including Node ID, function code 0x65, counter, ciphertext and tag — exactly
- Safety @en:integrated_drive_motors
- d_drive_motors:modbus_debug]] ===== Soft landing function ===== For vertical application, it is possible to activate a function call soft landing. This function executes automatically at every switch-off (Disable command via software o... the motor falls down every time is switched off. Function can be activate using NILAB Starter Software in M
- Pacdrive3 - Lxm62 servo drive @en:green_drive_motors
- typeplate file inside the flash you must use this function: {{:green_drive_motors:function.jpg?nolink&874x60|function.jpg}} It create a file inside the flash with the data of the structure ===== 4... u must delete any data inside the drive with this function block. {{:green_drive_motors:func_1.jpg?nolink&9
- Options @en:nela_actuator
- 0kg reserves 5kg allowance to activate anti pinch function. ==== Stroke Setting, Work With Switches. ==== ... es, adjust the stroke, and everything is done. **Function S**: Stroke setting, 2 sets of wiring (4 wires) t... t switches, push switches, tact switches, etc. **Function R:** With built-in reed switches and a magnetic r... sensed to stop at any position. {{:nela_actuator:function_r.jpg?direct&293x180}} ==== Hall Sensor for Accu
- Connectors and Pinout @en:green_drive_iso_rotolinear
- side with Speedtec M23 and M17 ==== |**PIN** |**FUNCTION** |**CONNECTOR VIEW FRONT** |**PIN** |**FUNCTION** | |12|SIN+/SLO+|{{:green_drive_iso:m23_m17.jpg?nolink&20... ide ===== Encoder type: Resolver 2p 7V 10KHz |**Function** |**Pin** | |Ref+|10| |Ref-|7| |Cos+|2| |Cos-|1|... 014 - 09010005** | |**BSTA 085 - 09020004** | |**Function** |**Pin** | |U|1| |V|2| |W|6| |PE|Earth| |-|4| |
- Connection system @en:green_drive_motors
- == ==== Stator side with Y-TEC ==== |**PIN** |**FUNCTION** |**CONNECTOR VIEW FRONT** |**PIN** |**FUNCTION** | |12|SIN+/SLO+|{{:green_drive_motors:ytec.jpg?nolink&20... side with Speedtec M23 and M17 ==== |**PIN** |**FUNCTION** |**CONNECTOR VIEW FRONT** |**PIN** |**FUNCTION** | |12|SIN+/SLO+|{{:green_drive_motors:m23_m17.jpg?nolink
- Connections - NLi080Q or NLi080X @en:integrated_drive_motors
- ION === |**PIN** |**SIGNAL** |**DESCRIPTION** |**FUNCTION** | |1|NC|NC| | |2|CAN_H|CAN HIGH| | |3|GND|Groun... IDE === |**PIN** |**SIGNAL** |**DESCRIPTION** |**FUNCTION** | |1|RS485_B|Modbus B| | |2|RS485_A|Modbus A| |... UB 15 \\ Pinout** |**SIGNAL** |**DESCRIPTION** |**FUNCTION** | |1|RS485_B|Modbus B| | |2|RS485_A|Modbus A| |... 0.jpg}} |**PIN** |**SIGNAL** |**DESCRIPTION** |**FUNCTION** | |9|DIG_OUT_2|Digital output 2 (24V logic, PNP
- MODBUS RTU Communication @en:integrated_drive_motors
- ode are : **1. Read Multiple Holding Registers - Function code 3** \\ **2. Write Single Holding Register - Function code 6** Please note that you can read a maximum... are organized in different area in respect to the function involved. |**PARAMETER AREA** |**STARTING ADDRES... nd Word - Address 4096 === Please note that with function code 6 (write register), the reply at this regist
- Glossary @en
- tion.\\ **Acceleration:** Change in velocity as a function of time, going from slower to faster.\\ **Accurac... otor.\\ **Deceleration:** Change in velocity as a function of time, going from faster to slower.\\ **Duty Cy... phases.\\ **Velocity:** A change in position as a function of time (speed).\\ **Velocity Amplifiers:** Servo
- Safe Torque Off @en:epulse
- This page describes the **Safe Torque Off (STO)** function of the Epulse10 servo drive. The STO inputs allow... _example_1.jpg}} ===== Safety PLC ===== The STO function can also be controlled by a safety system, for ex... ut so that the motor cannot produce torque. - The function is used for the safe stopping of the machine in a
- Safe Torque Off @en:gdi_ethercat
- This page describes the **Safe Torque Off (STO)** function of the GDi-EtherCAT motor. The STO inputs allow t... _example_1.jpg}} ===== Safety PLC ===== The STO function can also be controlled by a safety system, for ex... ut so that the motor cannot produce torque. - The function is used for the safe stopping of the machine in a
- Can Open Mode of Operation @en:integrated_drive_motors
- n|UINT32| ==== Control word bits 0x6040 - motion function ==== |**Bit position** |**Implemented Function** | |2|Quick stop| |4|Start the move| |6|Absolute or relati... s - 0x6041 ==== |**Bit position** |**Implemented Function** | |10|target reached| |12|setpoint acknowledge|
- Control Signals @en:integrated_pick_and_place
- atic Homing to reach the parking position.\\ This function is call Soft Landing and it is enabled by the par... y the Motor 2 Digital Output 3 set to In position function. After every Auto Homing the Motor 2 in position ... ting that the two motors complete the auto homing function waiting 3 secs or looking to the motor state usin
- NILAB Starter Software @en:nilab_starter
- repository for update on the field | | Auto-teach function for single and parallel motion | ==== Changelog ... Gateway values ## [2.4.1.3] - 05.3.2025 \\ - STO function added ## [2.4.1.2] - 10.2.2025 \\ - Bug fix Can ... dow ## Bug fixes \\ - Correct drive reset button function ## [2.3.0.12] - 23.12.2022 ### Bug fixes ###
- Alarm Codes @en:nl7_servo
- lt(Switch on disabled). Method 2： Use auxiliary function “AF_ACL” Press M to select auxiliary function , Press SET to enter into “AF_ACL” , Press and hold to clear the alarm Method 3： Set IO input function as Alarm clear input “ (A-CLR)”，refer to switch i